Many patio umbrella canopies will rip, fade, and lose their luster after a few years. It just happens, even with the best of fabrics. The sun beating on the fabric all day, harsh winds, repeated use, and the elements all take their toll on the umbrella canvas. Often the canopy will be in rough shape, but the underlying umbrella frame is still fine. If the ribs are still in good shape, the crank mechanisms still work, and the pole still looks good, it may make sense to get a replacement umbrella canopy rather than buying a whole new umbrella.
Purchasing a replacement canopy is often significantly cheaper than buying a whole new umbrella. If the frame is in good shape, you may even consider upgrading to a higher quality fabric like Sunbrella for your replacement canopy, which would give you a much higher end look, without spending the money on a whole new umbrella!
The biggest challenge is determining whether a given replacement umbrella canvas will fit your umbrella frame. For that reason, we have created this guide to ordering a patio umbrella canvas replacement.
Replacement Umbrella Canopy: How To Guide
Step 1: Determine the diameter of your umbrella canvas
If you can find the listing for your umbrella online, you will see how large the canopy is. Patio umbrella sizes may vary from 6′ to 13′ in diameter. If you can’t find the listing for your umbrella online, grab a tape measure and measure from the tip one of the umbrella ribs to the center umbrella pole. Double that distance, and you will have the umbrella canopy diameter.
Remember, an umbrella is not a flat plane, but rather is curved with the ribs on the bottom. Consequently, the canvas will actually be a little bit larger than this diameter measurement. Most umbrella replacement covers don’t supply an exact fit but will be close. They are generally broken down in 1′ increments (7′ umbrella canopy replacement cover, 8′ replacement cover, etc.).
Step 2: Count the Number of Ribs
The second major fit concern with a replacement canopy for patio umbrella is the number of ribs. Most umbrellas on the market have either 6 ribs or 8 ribs, but there are variations. And the replacement canvas must be configured for the same number of ribs as the original canvas.
Step 3: Note your Existing Canopy Ventilation
Take a look at how the ventilation works in your existing umbrella canopy. The vast majority of umbrella canopies have a single vent in the center, a top “hat” that channels air through the canopy, preventing the umbrella from flying away on a gusty day. However, there are other ventilation methods available like double venting umbrella canvases, and you must be sure to match the ventilation style in your market umbrella replacement canvas to your existing umbrella fabric.
There are not many double-vented patio umbrella canvas replacements around, but this one may fit your umbrella:
Last update on 2025-05-17 / Affiliate links / Images from Amazon Product Advertising API
Step 4: Remove the Existing Canopy
Gently remove the ribs from the sleeves of the existing canopy. Be careful not to bend the ribs to the point of breaking them! The first rib will be the most difficult, and once you have a couple of ribs off, the rest of the canopy should be easy to remove. You may want a second person to help with this step.
Step 5: Measure the Top Opening Size at the Center of the Canopy
Check the diameter of the hole at the center of the canopy. This will show how big the hole for the cap to be installed is. However, if this hole is too small, you can always cut it with scissors.
Step 6: Ensure That Your Existing Umbrella Frame is in Good Shape
- Check the ribs for rust, bending, and significant wear.
- Check your umbrella pole for peeling paint and rust
- Check your cranks and tilt mechanisms for weakness and fraying cords
If you find any significant concern with the umbrella frame, it probably doesn’t make sense to invest in a replacement patio umbrella canopy, as the frame may fail soon after installing the replacement umbrella.
Step 7: Order the New Canvas
Once you know your canvas size, the number of ribs, and the vent style, order your new canvas. We have a few suggestions below, which you may want to check out depending on your size and configuration needs. After the new canvas is ordered, below, we explain how to install the new canvas on the frame.
8′ Diameter, 6 Rib Replacement Canvas
If you have a patio umbrella with this configuration, you don’t have too many choices for umbrella canopy replacement. You may want to consider the Replacement Top Patio Umbrella Replacement Canopy cover. This replacement cover is only available in Tan and the canvas has a single wind vent in the center.
Unfortunately, there isn’t much information on these replacement covers, but this is not a common umbrella size configuration, so we hope that not many people will find themselves looking to replace these umbrella canvases.
No products found.
9′ Diameter, 6 Rib Replacement Canvas
Formosa Covers has a wide array of colors available on their 9′ diameter, 6 rib replacement covers. These 9 ft umbrella canopy replacement covers are made of 300 denier polyester fabric and are sprayed with a UV treatment and a water repellent. They feature a single air vent and come in a wide variety of color options (Shown here in Brick Red). These umbrella replacement canopies are very sturdy, Made in America, and are a great choice.
- Make sure your umbrella is 6 panels canopy with ribs length 52" to 54"
- 9ft umbrella replacement canopy for 6 ribs umbrella in Brick Red
- Fits 6 ribs umbrella frame ribs only from 52" to 54"
- 300 denier polyester fabric with UV treated and water repellent.
- This is Replacement umbrella CANOPY ONLY. Air vent canopy
Last update on 2025-05-17 / Affiliate links / Images from Amazon Product Advertising API
8′ Diameter, 8 Rib Replacement Umbrella Canopy
Yescom’s line of 8′ umbrella canopy replacements is a great place to start your research. Available in six different colors, these covers are made of 180g spun polyester, and treated with a UV30+ protectant. They are relatively inexpensive and come in a fun array of colors. The color fastness is not ideal, and in intense sun, they may fade.
Still, with the price point they are placed at, it is easy enough to purchase another replacement cover when needed.
Last update on 2025-05-17 / Affiliate links / Images from Amazon Product Advertising API
9′ Diameter, 8 Rib Umbrella Cover Replacement
There are several options available in this configuration, but we suggest the ExpectSaving line of market umbrella replacement canopies. Available in six different color options, and featuring a single wind vent, these 9 ft umbrella replacement canopy models are inexpensive, of high-quality materials, and look great. They are made of 180g polyester and are treated with a UV Protectant for sun and fade resistance.
Like many of the garden umbrella replacement canopy options in this price range, these look great for a while, but may not last under long-term exposure to the sun. Still, they are a great choice given their price range and are recommended.
Last update on 2025-05-17 / Affiliate links / Images from Amazon Product Advertising API
10′ Diameter 8 Rib Umbrella Replacement Canvas
The best option for those who have a 10′ diameter canvas is the Yescom line of 10′ replacement covers. These covers are available in three different colors and are of good quality at an aggressive price. Made of the same 180g polyester fabric as the 8′ covers above, this umbrella replacement fabric is UV30+ protected.
These canvases are water resistant, and will keep you dry in a soft rain, but are not waterproof.
This will fit 10′ cantilever umbrella frames, should you be looking for a cantilever umbrella replacement cover. However, you may need to cut the center hole a bit to make it fit on the cantilever umbrella frame.
These covers are not colorfast, and will only last so long. Still, at the price they are offered, they are a good deal.
Last update on 2025-05-17 / Affiliate links / Images from Amazon Product Advertising API
Cantilever Umbrella Replacement Canvas
Unfortunately, finding a replacement for a cantilever umbrella is usually more difficult than a patio umbrella. However, there are a few options out there, as long as your cantilever umbrella is an 8-rib model.
If you have a 10′ cantilever umbrella, these StrongCamel Replacement covers may work. And if you have an 11 or 12/’ umbrella, these BenefitUSA replacements may fit. Beyond that, you may want to try to contact your manufacturer.
Last update on 2025-05-17 / Affiliate links / Images from Amazon Product Advertising API
Step 8: Feed the Existing Rib Fingers Into the Canvas Umbrella Sleeves
It’s easiest to do this on one side of the umbrella when it is opened just a little bit. Push the ends of the ribs into the canopy sleeves, making sure that the sleeves are on the downward side of the canvas.
Work in a circle on successive ribs, either clockwise or counterclockwise. Having a second pair of hands to help hold the canopy as you install it can be helpful, too!
Step 9: Check the Fit, and Adjust If Necessary
Open and Close the Umbrella, and see how the new umbrella cover replacement looks on your frame. If it is too small, obviously you shouldn’t try to open the umbrella all the way, as it will rip. Return it, measure again, and order a different size.
If it is a bit too big, you can consider picking up some Rubber Leg Tips from your local home improvement store, which will fit over the ends of the umbrella ribs and add a bit of distance to the ribs. These tips will extend the overall length of the umbrella a bit and may make it tauter.
If the size is way too big, return and get a different umbrella canvas.
Conclusion: Patio Umbrella Replacement Canopy
By using an umbrella replacement cover, you can save a significant amount of money compared to purchasing a whole new umbrella, and you can refresh your patio with some new colors and designs without breaking the bank.
The process of finding the right umbrella cover for your umbrella is not difficult, and if you follow these steps, you’ll have a lovely new canvas in no time.
If getting replacement umbrella parts and installing them seems like too much time, you can always consider getting a new umbrella. Check out our a patio umbrella reviews if that’s the direction you want to take. Also, be sure to use an umbrella cover to keep your next patio umbrella canvas in great shape for as long as possible. And while you’re at it, you may want to add some patio umbrella lights or a patio umbrella heater to make your patio umbrella sing!
Happy Relaxing!
I have a frame with 8 ribs, of which 4 are 59″, and the other 4 are 43″, lengths arranged alternately. How do I get a replacement canopy? No manufacturer’s marks available
with wind, the umbrella turns over, the canvas actually goes sideways. What is wrong?
I am having a hard time finding a 10 ft,. 6 rib replacement canopy for my offset umbrella
I need to replace the canopy on my cantilever, 10′, 6 rib umbrella. Cannot find.
We have a Caribbean Shade umbrella purchased in South Africa 25 years ago. It is 13 ft square with 8 ribs. Center opening can vary but is 2 to 3 feet across. The slope from the center to the outside edge goes down 24″. We have replace the cover 3 times. The last replacement used Sunbrella material. Do you have a replacement or can have a replacement cover made? What would the cost be?
This was a big help. Can you suggest where to look for a 6.5-7ft 6 rib canopy replacement? Most places seem to have 9ft.
Thank You
These instructions seem pretty straight forward. Will they work for a 10 ft. 8 rib, cantilever style canopy as well?
My umbrella is different from the ones shown. Mine has 7 rib it is of course on a pool that sits in a 3×3 base fill with sand for ballast. It cantilevers over the object to be shaded. Is there a cover made for this type umbrella?
Thank you
Michella McCall
Seven-rib patio umbrellas are pretty unusual, unfortunately. You may be able to reach out to the original manufacturer and see if you can get a replacement through them, but finding an off-the-shelf replacement will be quite difficult. I can’t think of anyplace where I’ve seen 7-rib umbrella canvases. Good luck!
Please tell me the name of the manufacturer? I have 7 rib unit and I can not find anything.
I too have a 7 rib offset umbrella….3 to be exact. I have checked everywhere and can not find a replacement canvas. Any info on where to look or how to make one? Thank you….
I have a southern patio offset umbrella it has a Velcro opening at the top it has 6 ribs any idea where I can find replacement fabric thanks Ray
Six-rib offset umbrella canvases are a bit unusual. I’m afraid I don’t know where you’ll be able to find a replacement. You may be able to reach out to your original supplier, that’s probably your best bet. Good luck!
I have the same type of frame that Raymond has in a 6 panel, supported rib, 9’6″ model. Mine was from Southern Outdoor and apparently they have gone out of business or changed their name as I have not yet been able to find either the company OR the Velcro closure replacement canopy. The frame works perfectly and the crank is free.
If you have come across what I need then I’d be grateful to hear from you.
Thanks in advance,
Lawrence
what about an 8 rib 11 foot cantilever canopy? Where can I find a replacement?
Hi – any chance you know anything about a 10-rib 8′ canopy?
Thanks!
Michelle
We have an 11.5 ft, 8 rib umbrella with a hole in the TOP (not in the side as shown in other offerings). Can you suggest where we might find a replacement canopy?
I am trying to find a replacement for my 8 ribs crank rectangular umbrella and have a hard time finding this shape. Any suggestions on where to look?
I have an 8 rib cantilever umbrella with not identifying marks. I purchased a 11 ft replacement which will not allow the umbrella to be opened all the way. I have looked all over the internet and have not been able to find a 12 ft replacement. Any thoughts.
I am looking for a quality 6 rib rectangular umbrella canvas 6′ x 10′ with a single vent. Our original set came from Wood Classics but apparently they went out of business years ago. The umbrella stand is still in great shape so really hoping I can just replace the canvas. Any suggestions?
We have a 10′ cantilever 6 ribs x 57″ long. Where can we find a replacement canopy for it?
Looking for a replacement canopy 80 in 8 ribs wooden,
Do you make any ?
My umbrella has 8 ribs and is 7.5 ft. Do you have this size?
Looking for a double vented 9 feet 8 rib Off set
I have a 9ft 8 ribs solar umbrella that needs a new canopy. Can you suggest a company who sells replacement solar canopies. Thank you
I wish to change the color of my umbrella. It’s a Tuuci 7.5 x7.5 Classic Ocean Master, square, four ribs. I want a very good material.
This material looks very interesting I have an Ozark Trial 12ft x 12ft vented top portable canopy with a slanted leg. Do you make anything like this??
Any ideas where to find an approximate 78” diameter replacement for 6 ribs?
Thanks’
I need to replace the canopy on a rectangular umbrella. It is a wooden “pulley style” pull up . Do you have access to this style or where might I find it?
Our umbrella has 12 ribs and we are having no luck finding a replacement canopy. The cloth measure 9 ft across including the flaps; no flaps, 8ft across.
If we must go with a custom replacement, how much should we expect to pay? Any recommendations on where to go for a custom replacement? Thank you.
IMG_4888.PNG IMG
Do you have a replacement for a threshold umbrella 2016 RipLock 350
I’m looking for the color spa but would consider another color.
Thanks for your time. 😊
Do you have 10 ft 6 rib tan umbrella replacement canopy cover i need two
I can’t find a canopy replacement for my 10’ 6 rib offset umbrella.
Can you offer any advice on where to find a two-tier 8-ribbed outdoor umbrella?
We have a Hampton Bay 10’X10′ square cantilevered patio umbrella that we would like to get a new canopy for. It has 8 ribs – 4 long ones on the corners and 4 shorter ones on the side.
Do you carry this canopy?
I have a solar frame umbrella with 5 ribs and it is 8 ft. Is there a replacement cover for that?
Hello,
I need a 6 arm replacement canopy, size 9 feet across or 275cms, 4 feet 7 inches or 140 cms from top to bottom, & 4 feet or 122 cms between each arm. Currently canvas, & biege colour.
I will not buy Chinese goods now for obvious reasons, but saw some of your parasols were made in USA.
Can you let me know what you have to replace my existing cover please?
Kind Regards,
Mac Rutherford
I need a replacement double vented 9’ X 9’ square umbrella canopy.
Reached out to company & none are available. Will a 10’ square fit my cantilever frame?
Some years ago, I purchased a few parasols umbrellas from Indonesia, The canapys where made of cotton and mesured 300x300x280cm. Since, the colors have somewhat faded, so I`m looking to replace them. I`m having a hard time finding replacements of with these mesurements. Can you help me find a retailer were I can purchase replacements for my parasols
I need a 7 ribs canopy replacement and can not seem to find one. If Anyone know where I can find one , I would definitely appreciate if. I have been trying because the frame is in such good condition that I would hate to toss it out. Thanks In advance.
Looking to find a replacement canopy for our 11’ cantilever 8 rib umbrella- any ideas where we can find one?
Help please finding and eight rib. Four ribs are 69 inches long and four are 50 inches long, alternately. Has a 4 1/2 centre cap. Made of wood with a draw string pulley. No manufacturer name on frame.
I am looking for a replacement canopy with 6 ribs for a 10 ft. cantilever style umbrella. Anyone know where I can find one? The original was purchased in 2015 and is Sheldon brand.
I have a 11 ft cantilever style umbrella with 7 ribs-4 long and 3 short bought in 2017 I think it was a Wilson brand can’t find a replacement canopy it was bought with all around bugs net with Velcro at the top, please help.
I have a Christopher Knight 11 foot 8 ribs single vent umbrella. Can anyone post a link to a replacement?